MKU 10 G5, 3 cm Transverter
NEW - NEW - NEW
- Covering full 3 cm amateur radio band from 10000 MHz to 10500 MHz
- Flexible IF choice from 28 MHz to 440 MHz
- Very high spurious and harmonic rejection even at 28 MHz IF
- Low power IF mode
- Easy configuration of the transverter with our Kuhne Suite (works with Firmware V1.1)
- Covering full 3 cm amateur radio band from 10000 MHz to 10500 MHz
- Flexible IF choice from 28 MHz to 440 MHz
- Very high spurious and harmonic rejection even at 28 MHz IF
- Low power IF mode
- Easy configuration of the transverter with our Kuhne Suite (works with Firmware V1.1)
| RF range | 10000 ... 10500 MHz |
| IF range | 28 ... 440 MHz |
| IF input power | 0.5 ... 5 W, adjustable |
| LO accuracy @ 18 °C | typ. +/- 0.5 ppm (without ext. ref.) |
| LO frequency stability (-5 ... +55 °C) | typ. +/- 0.5 ppm (without ext. ref.) |
| Phase noise @ 1 kHz | typ. -94 dBc/Hz |
| Phase noise @ 10 kHz | typ. -103 dBc/Hz |
| Phase noise @ 100 kHz | typ. -105 dBc/Hz |
| Phase noise @ 1 MHz | typ. -123 dBc/Hz |
| Output power | min. 200 mW |
| Spurious rejection | typ. 50 dB |
| Harmonic rejection | typ. 48 dB |
| RX gain | typ. 25 dB |
| Noise figure @ 18 °C | typ. 1.3 dB |
| External reference input | 10 MHz / 2 ... 10 mW (sine or square wave) |
| Reference input connector | SMA-female, 50 ohms |
| PTT control | contact closure to ground or +12 V on the IF-cable |
| Supply voltage | +13.8 V DC (+12 ... 14 V DC) |
| Current consumption | typ. 580 mA |
| Case | milled aluminium |
| Dimensions (mm) | 100 x 80 x 14 |
| IF connectors / impedance | SMA-female, 50 Ohms |
| RF connectors / impedance | SMA-female, 50 ohms (separate RX/TX connectors) |
| Weight | 370 g (typ.) |
Find a detailed description under downloads.
- Covering full 3 cm amateur radio band from 10000 MHz to 10500 MHz
- Flexible IF choice from 28 MHz to 440 MHz
- Very high spurious and harmonic rejection even at 28 MHz IF
- Low power IF mode
- Input for an external 10 MHz reference source
- Local-Oscillator with high frequency stability VCTCXO
- IF range for RX and TX independent configurable
- Big attenuator at the IF input for input power up to 5 watts
- Fuses are self-resettable (polyfuses)
- Low noise converter in the receive path
- Transmit gain and receive gain separately adjustable
- Control output for additional amplifier stages or a coaxial relay
- Adjustable sequencer delay
- PTT can be switched by a voltage on the IF connector or by connecting the PTT pin to ground
- Detector output (DC voltage) for monitoring the output power
Applikation MKU 10 G5 - MKU PA 3CM-2W A
Applikation MKU 10 G5 - MKU PA 3CM-4W A
Applikation MKU 10 G5 - MKU PA 3CM-8W A
Applikation MKU 10 G5 - MKU PA 3CM-30W A
Applikation MKU 10 G5 - MKU PA 3CM-60W B
Applikation MKU 10 G5 - MKU PA 3CM-4W A
Applikation MKU 10 G5 - MKU PA 3CM-8W A
Applikation MKU 10 G5 - MKU PA 3CM-30W A
Applikation MKU 10 G5 - MKU PA 3CM-60W B
